Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Page 70 Operating Manual Download

Page: 70 / 154

Step by Step

Conducting calls – enhanced functions

Deleting an entry or phonebook

When the handset is idle: Open the phonebook.

Select the required entry.

Open the menu.

either:

[

Select the menu item and confirm. The telephone
number is deleted.

or:

[

Select the menu item and confirm. A security check
question appears.

Confirm the security check question. The phonebook is
deleted.

Press the On-hook key to end the operation.

Displaying available memory

When the handset is idle: Open the phonebook.

Select any entry.

Open the menu.

[

Select the menu item and confirm. The amount of
memory used and available is displayed.

Press the On-hook key to end the operation.

Options

Delete Entry

Delete List

Yes

Options

Available Memory

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands

Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional, Operating Manual

Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands