Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Operating Manual Download Page 31 | Manualshive

Page: 31 / 154

background image

Putting the handset into service

21

Battery pack operating times and charging time

The operating times are only achieved after several charging and discharg-
ing cycles.

The handset’s standby time is significantly increased by deactivating the
backlight.

Permitted battery packs

Only the original Siemens battery pack is permitted for the handset.

Capacity (mAh)

Stand-by mode
(hours)

Talk time
(hours)

Charging
time
(hours)

1000
(original battery pack)

approx. 380 (16 days),
prerequisite: no back-
light

approx. 12

approx. 3.7

Battery pack

Part number

For Gigaset M2 professional:
Lithium-Ion, 1000 mAh

A5B00075416005

For Gigaset M2 Ex professional:
Lithium-Ion, 1000 mAh, including electronic
components)

A5B00075609027

Danger of explosion:

Local and operational factors may lead to an explosive atmosphere
in an Ex zone. Never open the handset battery compartment in an
Ex zone.

Attention:

For Gigaset M2 Ex professional:

Only use approved Ex battery

packs (see the "Permitted battery packs" section in the operating
manual). Ex authorisation is only valid and the handset can only be
operated if this battery pack is installed. Other battery packs are
strictly prohibited. If they are used, Ex protection is no longer valid.

«
...
29
30
31
32
33
...
»

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Reviews:

No comments

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brand: Samsung Pages: 22

Brand: Talkswitch Pages: 29

Brand: Talkswitch Pages: 3

Brand: mPTech Pages: 50

Brand: BTECH Pages: 60

SimplePhone A50

Brand: Tesla Pages: 32

Brand: Plum Mobile Pages: 15

Brand: AMGOO Pages: 44

Brand: Pantech Pages: 82

Brand: switel Pages: 4

Brand: Samsung Pages: 110

Brand: Samsung Pages: 84

Brand: Samsung Pages: 140

Brand: Avaya Pages: 86

Brand: Geemarc Pages: 69

Brand: Geemarc Pages: 81

Clearsound CL8400

Brand: Geemarc Pages: 102

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands