manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 98 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 98

Fault – Cause – Remedy

98

Instructions for Use Carina SW 3.n

External power failure

!!

The device has no external 
power supply.

Check the mains supply or DC 
power supply.

The mains plug or DC plug is 
loose. 

Insert the mains plug or DC 
plug properly at both ends.

The mains cable or DC cable 
has a break.

Change the cable.

Mains power failure.

Connect a replacement bat-
tery.

The external battery is flat. 

Connect to the mains. Charge 
external battery.

High frequency

!!!

Patient is breathing at a high 
spontaneous frequency, there-
fore the monitored overall fre-
quency is too high. The alarm 
is not active in ventilation mode 
PC-BIPAP and VC-SIMV.

Check condition of patient, 
check ventilation pattern, cor-
rect alarm limit if necessary.

Hose system incorrect

!!!

Only for a hose system with 
leak valve. 
The hose system connected 
does not correspond to the 
device setting.

Use the correct hose system. 
Or:
Correct the device setting. 

Inlet filter missing

!!

The inlet filter has been 
removed or is not inserted cor-
rectly.

Insert inlet filter. Check that the 
inlet filter is secure.

Insp. temperature high
(in log book »Insp. temperature 
high !!!«)

!!!

Breathing gas temperature 
above 40 °C.

Make sure the ambient temper-
ature drops.

Int. battery activated

!

Owing to the lack of an external 
power supply (mains or exter-
nal battery) the device is being 
supplied from the internal bat-
tery.

Reconnect the mains voltage 
or supply from a charged exter-
nal battery.

Int. battery empty

!!!

Owing to the lack of an external 
power supply (mains or exter-
nal battery) the device is being 
supplied from the internal bat-
tery. The operating time with 
supply from the internal battery 
has expired. 

Connect ventilator immediately 
to mains power supply or to a 
fully charged external battery.

Error message

Cause

Remedy

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments