manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 97 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 97

Instructions for Use Carina SW 3.n

97

Fault – Cause – Remedy

Battery indication not reliable

!

Battery indication is not relia-
ble.

Proceed the action on page 82.
If the problem persists call 
DrägerService.

Blower overheated
(in log book »Blower over-
heated !!!«)

!!!

The blower has overheated. 
The device is operating at 
reduced output. Ventilation is 
not optimal.

Make sure air is being supplied 
to the device. If there is a free 
supply of air: Use a replace-
ment device. 
Call DrägerService.

Check settings
(in log book 
»Check settings !!«)

!!

Loss of saved settings. Carina 
operates with the default set-
tings.

Confirm with rotary knob. Use 
a replacement device. 
Call DrägerService.

Continuous Paw high
(in log book »Continuous Paw 
high !!!«)

!!!

Expiratory valve obstructed.

Check expiratory valve.

Continuous Paw low
(in log book »Continuous Paw 
low !!!«)

!!!

Note: This error is only sig-
nalled after 5 to 30 seconds. 
Air supply blocked. The ventila-
tion function is not optimal. 
Hose system blocked or leak-
ing.

Make sure there is a free sup-
ply of air. If there is a free sup-
ply of air: Check the hose 
system, filters and other com-
ponents for free-flow and 
leaks. Use a replacement 
device. Call DrägerService.

Device failure
(in log book 
»Device failure !!!«)

!!!

The device has a fatal techni-
cal problem. Ventilation has 
failed.

Immediately disconnect the 
patient from Carina and con-
tinue ventilation using a differ-
ent ventilator.
If the device cannot be turned 
off, remove the O

2

 hose from 

the central supply and then 
turn off the device.
Call DrägerService.

Disconnection/high leakage

!

Disconnection of the hose or  
large leakage is detected.

 

After the leakage alarm, Carina 
delivers a low constant flow at 
PEEP level. When the leak has 
been eliminated, Carina auto-
matically resumes operation at 
the previous ventilation set-
tings.

Check hoses, filters and other 
components to make sure the 
connections are not leaking 
and are secure.

Error message

Cause

Remedy

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments