Siemens Drager medical Carina Instructions For Use Manual Download Page 28

Page: 28 / 144

Operating concept

Instructions for Use Carina SW 3.n

Display of relevant ventilation parameters
1

When setting a ventilation parameter the rele-
vant ventilation values calculated by Carina are
indicated in the display field for »

Value 1

«.

When the setting has been confirmed, the dis-
play field closes.

Colour concept

Setting ventilation mode

Press button for the ventilation mode displayed.

To select ventilation mode, turn rotary knob.

To confirm, press rotary knob.

Setting ventilation parameters

Press button for the ventilation parameter.

To set the value, turn rotary knob.
To confirm, press rotary knob.

Yellow

Function/parameter selected, not
yet confirmed

Dark green

Button can be used
Function/parameter confirmed

Grey

Function/parameter cannot be
used

501

506

508

080

Summary of Contents for Drager medical Carina

















































































































































Search results

Summary of Contents for Drager medical Carina

Reviews:

Siemens Drager medical Carina, Instructions For Use Manual, Page: 28 / 144

Search results

Summary of Contents for Drager medical Carina

Reviews: