manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 144 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 144

These Instructions for Use only apply to

Carina SW 3.n

with the Serial No.:
If no Serial No. has been filled in by Dräger, 
these Instructions for Use are provided for 
general information only and are not 
intended for use with any specific machine 
or device.
This document is provided for customer 
information only, and will not be updated or 
exchanged without customer request.

Directive 93/42/EEC
concerning Medical Devices

 Manufacturer

Dräger Medical AG & Co. KG 

Moislinger Allee 53 – 55
D-23542 Lübeck
Germany
+49 451 8 82-0

FAX

+49 451 8 82-20 80
http://www.draeger.com

90 38 907

 – GA 5665.700 en RI 12

© Dräger Medical AG & Co. KG
6th edition – December 2008 
(1st edition – February 2006)
Dräger reserves the right to make modifi-
cations to the equipment without prior 
notice.

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments