Siemens Drager medical Carina Instructions For Use Manual Download Page 26

Page: 26 / 144

Operating concept

Instructions for Use Carina SW 3.n

Control panel

Centre rotary knob
1

For setting and confirming functions and venti-
lation parameters.

To set the value, turn rotary knob.

To confirm, press rotary knob.

Buttons with a fixed function
2

Audio paused 2 min.

« button for switching off

the alarm tone for 2 minutes.

Select Menu

« button to call up the menus

(ventilation settings, alarms, measured values,
configuration, interlock).

Start/Standby

« button to switch between

standby and ventilation.

Buttons for calling up functions and ventilation
parameters
5

Pressing the button opens the relevant function
displayed on the screen or the relevant ventila-
tion parameter.

Power supply display
6

Green LED

Dwell time without inputs

If a changed setting or selection is not confirmed
with the rotary knob for more than 30 seconds, the
previous state is reactivated.

Flashing: External power supply is connected

(mains/external battery), internal battery
is being charged.

Lit:

External power supply is connected
(mains/external battery), internal battery
is fully charged.

Off:

External power supply is not connected,
device is being operated from a battery.

076

Summary of Contents for Drager medical Carina

















































































































































Search results

Summary of Contents for Drager medical Carina

Reviews:

Siemens Drager medical Carina, Instructions For Use Manual, Page: 26 / 144

Search results

Summary of Contents for Drager medical Carina

Reviews: