manualshive.com logo in svg

Siemens Drager medical Carina, Instructions For Use Manual, Page: 105 / 144

Share
Download
Siemens Drager medical Carina Instructions For Use Manual Download Page 105

Instructions for Use Carina SW 3.n

105

Cleaning, Disinfection and Sterilisation

Care list

Dismantling the components

z

Switch off the device and respiratory gas 
humidifier.

z

Disconnect mains plug.

1

Drain condensate from water traps.

2

Drain the water container of the humidifier.

z

Remove expiratory valve or leak valve. Remove 
pilot line of the expiratory valve.

z

Remove the inlet filter of the basic device.

Respiratory gas humidifier, medication 
nebulizer

z

Dismantle according to the relevant instructions 
for use.

Ventilation hoses

z

Remove from the nozzles.

z

To remove the ventilation hoses, always 
hold them at the connection sleeves and not 
the spiral ribbing!

Otherwise the spiral ribbing may become 
detached, e.g. at the connection sleeve, or the 
hose can be torn out of the sleeve.

z

Drain condensate from ventilation hoses.

z

Disinfect and clean ventilation hoses, water 
traps and their removed collecting jars.

What 
Cleanable components

How often
Recommended cleaning 
intervals

How

Carina basic device

per patient

Dismantle, clean and if applicable wipe 
disinfect

Trolley
Compressed gas hose
Hinged arm

per patient

Dismantle, clean and if applicable wipe 
disinfect

Reusable ventilation hoses
Reusable water trap

per patient/weekly

Dismantle, clean and disinfect in the 
cleaning and disinfection machine at 
93 °C/10 minutes with detergents only. 
Hot steam sterilisation at 134 °C.

048

2

1

084

Summary of Contents for Drager medical Carina

















































































































































Reviews:

No comments