ShopBot PRS Assembly Manual Download Page 38 | Manualshive

Page: 38 / 54

background image

pg.

38

Mounting a 16” VFD

Locate the three pairs of holes on the center leg of the front side of your table. The 16” VFD will attach

to the

upper and lower pairs

(skip the middle pair). Attach the first mounting strap to the table leg as

shown here, using a 1/4-20 x 5/8” flat head screw, washer, and nylock nut. Repeat with the other

mounting strap on the upper pair of holes.

Align the mounting holes at the corners of

the VFD with the remaining holes on the

mounting straps. On the right side of the

VFD, thread a 1/4-20 x 3/4” button head

screw through the VFD, strap, and table leg.

Secure using washer and nylock nut. On the

left side of the VFD, the hardware will go

through the VFD and strap only.

This completes the mounting procedure for

the 16” VFD.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
36
37
38
39
40
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: Vahle Pages: 96

Brand: EASTERN INSTRUMENTS Pages: 93

Brand: Pari Pages: 2

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: Hällde Pages: 40

Brand: Hällde Pages: 6

Brand: M-system Pages: 2

Brand: Rico Pages: 34

Frontier FC5706

Brand: OHAUS Pages: 47

Brand: Ocutech Pages: 4

Brand: OHAUS Pages: 84

Brand: Yamaha Pages: 5

Brand: rbd instruments Pages: 18

Brand: LSI Pages: 24

Brand: B medical systems Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands