ShopBot PRS Assembly Manual Download Page 22 | Manualshive

Page: 22 / 54

background image

pg.

22

Square the rear table side

Measure the table across both diagonals. The measurements should be the same (to within 1/16”).

If your measurements are the same, skip this step and move on to mounting the table surface.

If your measurements are different, you will need to adjust the rear table side. Before continuing, check

the bolts holding the cross-supports onto the rear table side and ensure that they are loose enough to

slide within the grooves.

The example shown here is exaggerated to illustrate the correct method of squaring your table:

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
20
21
22
23
24
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: B-K lighting Pages: 3

Brand: Garmin Pages: 2

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: Rational Pages: 16

Brand: Zero 88 Pages: 12

Brand: Zeiss Pages: 119

Brand: Zehnder Rittling Pages: 32

Brand: GE Pages: 37

Exitronix LEMD Series

Brand: BARRON Pages: 6

Brand: SCHUNK Pages: 2

So-exercise TX7

Brand: T-SoX Pages: 8

Brand: Kattsafe Pages: 19

Team Agile Color Tune TM16-0

Brand: GRAU Pages: 24

Dual SD/HD Video Delay VLD-1002-MD

Brand: Algolith Pages: 30

Brand: Fuji Electric Pages: 39

Brand: Twinkly Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands