ShopBot PRS Assembly Manual Download Page 32 | Manualshive

Page: 32 / 54

background image

pg.

32

Secure the motor cables

If this is a PRSalpha tool, the motor cables will already be attached to the motor. For PRSstandard tools, you will

need to connect the motor cables first. The motor cables are labeled and color-coded. Just match each cable to its

motor and connect the gray Wago plug.

RIGHT: both ends tightly connected

WRONG: notice the gap on the right side

Link three wire ties together to create one long tie. For each motor, wrap the motor cable back towards the motor

housing and secure it with the linked tie.

This will keep the cables safely out of the way, and create a stress-relief

point and help to prevent damage to the motor in case the cables ever snag or pull.

Leave the other end of the motor cables loose for now. We will run them back to the control box once

the Y and X axis E-chain (the cable management system) are installed.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
30
31
32
33
34
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: FagronLab Pages: 16

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Parker Pages: 24

Brand: Aveo Engineering Pages: 16

Brand: Ublox Pages: 22

Brand: v.link Pages: 20

Brand: BCP Pages: 8

APPLETON EBR 30 Series

Brand: EGS Pages: 2

LED MINI TRI PAR CAN 3 W

Brand: Cameo Pages: 110

Brand: Allard Pages: 12

Agilium Reactive 50K324-US

Brand: Otto Bock Pages: 16

Brand: HAMPTON BAY Pages: 4

Brand: EZ Digital Pages: 53

Brand: Defibtech Pages: 12

Brand: CAMP Pages: 156

Brand: Datex-Ohmeda Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands