ShopBot PRS Assembly Manual Download Page 14 | Manualshive

Page: 14 / 54

background image

pg.

14

Attach the lower support

Use the same order of

1/2” hardware (hex

bolt and flat washer on one side—flat

washer, lock washer, and hex nut on the

back side)

to secure the lower support to

the first set of table legs.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
12
13
14
15
16
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: Hanil Pages: 60

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Dynapro ET 355 Monitor HL

Brand: 3M Pages: 23

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: RASHA PROFESSIONAL Pages: 11

Brand: MADRIX Pages: 24

Brand: MADRIX Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands