ShopBot PRS Assembly Manual Download Page 54

Page: 54 / 54

pg.

Spoilboard

The

spoilboard

is a sacrificial layer of 3/4” Medium-Density Fiberboard (MDF). As it gets damaged over time, you

can re-surface the board down to a perfectly flat work surface until the entire board has been used up, then simply

replace it with a new sheet.

For this step, you will need about a gallon of wood glue.



Spread a thin, even coat of glue across the entire surface of the base layer. A cheap paint roller works

great.



Have someone help you set the MDF sheet(s) onto the base. Align this layer so that it lines up flush with

the edge of the base, and work quickly- the glue will start to set within a minute.



For best results, drive a handful of 1 1/2” wood screws into the MDF to clamp it to the base.

Be sure to

remove these screws

after 30 minutes.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

Summary of Contents for PRS























































Search results

Summary of Contents for PRS

Reviews:

Related manuals for PRS

Brands by name

Popular brands

ShopBot PRS, Assembly Manual

Search results

Summary of Contents for PRS

Reviews:

Related manuals for PRS

Brands by name

Popular brands