ShopBot PRS Assembly Manual Download Page 35 | Manualshive

Page: 35 / 54

background image

pg.

35

Mounting the VFD (Applies to spindles only. Skip this section if you are using a

router).

The Variable Frequency Drive (VFD) controls the speed of the spindle. It mounts to the table frame using the

hardware kit labeled “VFD mounting kit.”

Depending on the horsepower of your spindle, you will have either a 10” or 16” VFD. Both sizes use the same

mounting hardware, but placement is slightly different.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
33
34
35
36
37
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: Rain-Flo Irrigation Pages: 16

Brand: Haag-Streit Pages: 16

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: RaycoWylie Pages: 9

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brand: Ravo Pages: 114

Brand: Alcoscan Pages: 6

Cutler-Hammer ATC-300

Brand: Eaton Pages: 32

Brand: K-SPORT Pages: 5

Brand: Raytec Pages: 8

Brand: DALBO Pages: 27

Infinity Wash XL

Brand: Coemar Pages: 6

Brand: Cleaver Scientific Pages: 41

Brand: WESTEK Pages: 4

Brand: Karma Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands