ShopBot PRS Assembly Manual Download Page 34 | Manualshive

Page: 34 / 54

background image

pg.

34

To square the spindle:

Position the spindle over the table surface. Place

a square between the table surface and the side of the spindle,

as shown here. Adjust the position of the spindle as needed.

Once the spindle is square, tighten the

bolts using the pictured pattern to

ensure that they are fully tightened.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
32
33
34
35
36
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: Rabe Pages: 65

Brand: 3M Pages: 2

Brand: FEAS Pages: 72

Brand: KaVo Pages: 49

Brand: Easson Pages: 33

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: Nederman Pages: 89

Brand: Nederman Pages: 71

Brand: Nederman Pages: 131

Brand: X-Cite Pages: 2

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brand: T&D Pages: 28

Brand: Teac Pages: 76

Brand: Teac Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands