ShopBot PRS Assembly Manual Download Page 29 | Manualshive

Page: 29 / 54

background image

pg.

29

Attach the rail wipers

The rail wipers are designed to keep the wheels and v-rails free of excessive dust and debris. This will greatly

prolong the service life of your wheels and allow for smooth, accurate operation of the YZ car.

The Y axis wiper kit includes 4 wiper caps with foam inserts and mounting hardware.



Use caution when opening the individual bags so that you don’t lose any of the small mounting screws.



Place the foam inserts into the wipers and saturate with lightweight machine oil (not included).



Secure a wiper assembly over each wheel on the YZ car with the included mounting screws. Do not

overtighten.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
27
28
29
30
31
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: Bartscher Pages: 22

Brand: Panasonic Pages: 9

Brand: Above All Pages: 4

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brand: Ultrasport Pages: 72

Brand: Wieland Pages: 2

41370 Micro Spot

Brand: SHOWTEC Pages: 22

Brand: Carestream Pages: 64

Brand: Osram Pages: 4

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: SCHUNK Pages: 2

Brand: Coba Pages: 2

Brand: Bowa Pages: 140

Brand: Toparc Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands