ShopBot PRS Assembly Manual Download Page 41 | Manualshive

Page: 41 / 54

background image

pg.

41

Install the proximity switches

The proximity switches are used to calibrate the XY location of the tool, and also signal the tool to stop movement

before hitting the mechanical end stops. They are triggered by a steel target (in this case, a hex bolt).

Start by installing the X axis switch targets on the

rear table side

. Slide one of the T-nuts into the lower middle

groove of the extrusion. Thread a hex nut onto one of the hex bolts, add a flat washer, and then loosely thread the

bolt into the T-nut. Adjust the position of this assembly according to the diagram below. Tighten the bolt into the

T-nut and then tighten the hex nut down against the extrusion.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
39
40
41
42
43
...
»

Summary of Contents for PRS























































Reviews:

No comments

Related manuals for PRS

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: Taurus Pages: 24

Brand: Wahl Pages: 2

Brand: IEMCA Pages: 82

KID 80-IV Touch

Brand: IEMCA Pages: 122

Brand: Calrec Pages: 92

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: Kattsafe Pages: 19

500 FleetBroadband

Brand: Sailor Pages: 20

Brand: Dräger Medical Pages: 204

Brand: K-SPORT Pages: 5

Brand: Brillion Pages: 56

Brand: HYDRA-RIB Pages: 25

Brand: Osprey Medical Pages: 49

Brand: Lightolier Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands