manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 84 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 84

 

 

5-4 

SANRAD V-Switch CLI User Manual

 

RAID controller are simultaneously exposed through all ports connected 
to both V-Switches for the V-Switches to provide high availability during a 
V-Switch failover. 

In Figure 

 

5-2, V-Switch 1 has gone off-line.  V-Switch 2 activates V-Switch 1’s IP 

address and takes over exposure of Volume 1 to Host 1, represented by the 
orange dashed line. 

Host 1 continues to access Volume 1 through the same IP address as it did 
before its V-Switch went off-line.  Host 1 has no way of knowing that its regular 
V-Switch is off-line.  Host 1’s storage performance is not impacted by the off-
line V-Switch. 

10

2

6

8

Cloud

IP SAN

IP1-inactive
IP2-inactive

IP2-active
IP1-active

Tower box

Host 2

iSCSI

initiator

Vol 2

Vol 1

Tower box

Host 1

iSCSI

initiator

V Switch 1

V Switch 2

Disk 1

Disk 2

Disk 4

Disk 3

iSCSI Target 2

wwui2

iSCSI Target 1

wwui1

Vol 2

LU0

Vol 1

LU0

IP1,Target 1

IP2,Target 2

JBOD

 

Figure 

 

5-2.  Re-routing Storage Access with Off-line V-Switch 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments