manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 206 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 206

 

 

10-20 

SANRAD V-Switch CLI  User Manual

 

 

 

V-Switch 3000 Power Supply 

The V-Switch 3000 is standard-issued with two hot-swappable AC power 
supplies.  If one of the power supplies fail, its red LED on the back panel turns 
off.  If both of the power supplies fail, the Power LED on the front panel turns 
off. 

STEP 1.

 

D

ISCONNECT THE POWER CABLE

 

Disconnect the power cable from the power source.  After the power cable 
is disconnected from the power source, disconnect the power cable from 
the V-Switch. 

STEP 2.

 

L

OOSEN THE POWER SUPPLY CONNECTING SCREW

 

Loosen the power supply connecting screw to release the power supply 
from the V-Switch. 

STEP 3.

 

R

EMOVE THE POWER SUPPLY

 

Lift the power supply handle and pull to slide the power supply out 

1024

3

connecting

screw

handle

 

Figure 

 

10-3.  Replacing a Power Supply 

STEP 4.

 

INSERT A FUNCTIONING COMPATIBLE POWER SUPPLY AND SECURE

 

Insert a functioning compatible power supply.  Secure the power supply to 
the V-Switch. 

It is now safe to reconnect the power cable to the power supply and power 
source. 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments