manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 71 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 71

 

 

Chapter 4:  V-Switch Configuration  

4-19

 

 

Configuring iSCSI Portals 

Do not create an 

iSCSI portal on the 

management IP 

address. 

 

The V-Switch 

supports a maximum 

of 100 portals. 

To enable communication between iSCSI initiators and iSCSI targets you 
need to assign a portal to the iSCSI protocol transport.  Use the CLI 
command 

iscsi portal create

 to create an iSCSI portal.  A portal is 

the coupling of an IP address and a TCP port.  Once created, a portal is 
opened automatically during a communication session.  If you are 
working in a V-Switch cluster, each portal must be created on both V-
Switches in the V-Switch cluster.  For more information on V-Switch 
clusters, see “

Introduction to V-Switch Clusters

”. 

iscsi portal create 

You need to define two parameters to configure an iSCSI portal: 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-ip 

IP

 ADDRESS

 

U

SER

-

ASSIGNED 

NETWORK PORT 

IP

 

ADDRESS

 

MANDATORY

 

212.199.43.66 

 

-p 

TCP

 PORT

 TCP

 PORT 

THROUGH WHICH 
THE I

SCSI

 

PROTOCOL PASSES

 

O

PTIONAL

 

DEFAULT

:

  

3260 

 

Example: 

An iSCSI portal is created using the default TCP port 3260 for the IP address 
212.199.43.66. 

iscsi portal create –ip 212.199.43.66 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments