SANRAD I3.1.1205 User Manual Download Page 149

Page: 149 / 348

Chapter 7: Volume Exposure and Security

7-31

You need to define six parameters to create and expose an iSCSI target and
volume LUN:

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-new

NEW TARGET

NEW I

SCSI

TARGET

TO CREATE

OPTIONAL

No parameter
required

-vol

VOLUME ALIAS

ALIAS OF VOLUME
TO CREATE

LU0

AND TARGET FOR

MANDATORY

Vol1

-ta

TARGET ALIAS

SER

ASSIGNED

ALIAS OF TARGET
TO CREATE

MANDATORY

finance

-lun

NUMBER

SER

ASSIGNED

LUN

FOR EXPOSING

VOLUME

MANDATORY

ON EXISTING
TARGET

-tn

TARGET WWUI

SER

ASSIGNED

WORLD WIDE
UNIQUE IDENTIFIER
FOR THE TARGET

MANDATORY ON
A NEW TARGET

sanrad.
billing

-device

DEVICE

ALIAS OF

V-

WITCH TO EXPOSE

TARGET ON

MANDATORY ON
A NEW TARGET

VSwitch1

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 149 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: