SANRAD I3.1.1205 User Manual Download Page 266

Page: 266 / 348

11-52

SANRAD V-Switch CLI User Manual

scsi target port statistics

This command shows all details of the SCSI target ports.

scsi target port statistics

Table

11-38: SCSI Target Port Statistics

Target Port

Trans

Commands

Read MB

Written MB

Oracle

0 iSCSI

1900 10000

10900

1 iSCSI

1800 9990 10000

iscsi rinitiator show

This command shows all remote initiators.

iscsi rinitiator show

Table

11-39: Remote iSCSI Initiators

Target Alias

Initiator Alias

Initiator Name

nms154dr iqn.1991-05.com.micr

iqn.1991-05.com.micr

nms155dr

iqn.1991-05.com.micr

iscsi rinitiator list

This command lists all remote initiators connected to a specific target.

iscsi rinitiator list

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-ta

TARGET ALIAS

ALIAS OF TARGET
FOR STATISTICS

MANDATORY

Finance

Table

11-40: Remote iSCSI Initiators for a Specific Target

Name Alias

ISID

iqn.1991*~ iqn.1991*~

40001370000

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 266 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: