manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 275 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 275

 

 

Chapter 11:  Command Line Interface  

11-61

 

acl identity add srp 

This command adds SRP authentication credentials to an identity. 

acl identity add srp 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-id 

IDENTITY

 

NAME OF 

ACL 

MANDATORY

 

Med_School 

 

-un 

USER NAME

 

HOST NAME

 

MANDATORY

 

Robert 

 

-pw 

USER PASSWORD

 

HOST PASSWORD

 

MANDATORY

 

cardiac 

acl identity remove srp 

This command removes an SRP authentication credential from an identity. 

acl identity remove srp 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-id 

IDENTITY

 

NAME OF 

ACL 

MANDATORY

 

Med_School 

 

-un 

USER NAME

 

HOST NAME

 

MANDATORY

 

Robert 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments