manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 79 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 79

 

 

Chapter 4:  V-Switch Configuration  

4-27

 

 

ip route remove 

You need three parameters to remove an IP routing path. 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-dip 

DESTINATION 

IP IP

 OF HOST 

STATION

 

MANDATORY

 

10.12.40.0 

 

-dmask 

DESTINATION 
MASK

 

IP

 MASK OF HOST 

STATION

 

MANDATORY

 

255.255.255.0 

 

-if 

INTERFACE 
ALIAS

 

NETWORK PORT TO 
OPEN 
COMMUNICATION 
THROUGH

 

MANDATORY

 

eth3 

Example: 

The routing path to destination network IP 10.12.40.0 (IP mask 255.255.255.0) is 
removed from network port Eth3. 

ip route remove –dip 10.12.40.0 –dmask 255.255.255.0 –if 
eth3 

You have now configured all basic V-Switch parameters.    If you are creating a 
V-Switch cluster, continue with “

Configuring a Cluster

”.  If you are still 

working with a single V-Switch, you can now begin creating virtual volumes.  
Continue with “

Chapter 6. Volume Configuration

”.  

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments