SANRAD I3.1.1205 User Manual Download Page 222

Page: 222 / 348

11-8

SANRAD V-Switch CLI User Manual

Name

Switch1

Description

SW Version 1.5, build 5,patch 0
Board version 1, PCB version

WWNN

20:00:20:10:58:00:10:46

Function

Gateway

fc set speed

This command allows you to set the speed of the FC communication.

fc set speed

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-if

INTERFACE

STORAGE PORT

MANDATORY

fc2

-sp

SPEED

COMMUNICATION
SPEED

MANDATORY

GB:

DEFAULT

interface show

This command shows the V Switch interfaces (ports) and their parameters.

interface show

Table

11-4: V Switch Interfaces

Type

Name

Description

Alias

Phys

Address

RS232

cons RS232 Management Int

cons 000000000000

ETHERNET

mgmt Fast Ethernet Manage

mgmt 000000000000

FibreChannel

fc1

MMF

fc1

000000000000

FibreChannel

fc2

MMF

fc2

000000000000

FibreChannel

fc3

MMF

fc3

000000000000

FibreChannel

fc4

MMF

fc4

000000000000

FibreChannel

fc5

MMF

fc5

000000000000

FibreChannel

fc6

MMF

fc6

000000000000

ETHERNET

eth1 Gigabit Ethernet Net

eth1 00081a000110

ETHERNET

eth2 Gigabit Ethernet Net

eth2 00081a000111

ETHERNET

eth3 Gigabit Ethernet Net

eth3 00081a000112

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 222 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: