SANRAD I3.1.1205 User Manual Download Page 204

Page: 204 / 348

10-18

SANRAD V-Switch CLI User Manual

Clusters

Modifying Neighbor Parameters

You can modify neighbor parameters in a cluster.

neighbor set

You need to define up to two parameters to modify a neighbor’s
parameters in a cluster:

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-nb

NEIGHBOR

ALIAS OF
NEIGHBORING

V-

WITCH IN

CLUSTER

MANDATORY IF
CHANGING

NewVSwitch

-ip

ADDRESS

MANAGEMENT

ADDRESS OF

EIGHBOR

MANDATORY IF
CHANGING

212.199.43.40

Removing a Neighbor

Both V-Switches

must have its

neighbor removed.

You can remove a neighbor from a cluster.

neighbor remove

You need to define one parameter to remove a neighbor from a cluster:

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-nb

NEIGHBOR

ALIAS OF
NEIGHBORING

V-

WITCH IN

CLUSTER

MANDATORY IF
CHANGING

NewVSwitch

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 204 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: