SANRAD I3.1.1205 User Manual Download Page 276

Page: 276 / 348

11-62

SANRAD V-Switch CLI User Manual

acl identity set

This command allows changes to an identity.

acl identity set

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-id

IDENTITY

NAME OF

ACL

MANDATORY

Med_School

-na

NEW ALAIS

NEW ALAIS FOR
IDENTITY

OPTIONAL

Medschool

-info

INFORMATION

INFORMATION ON
IDENTITY

OPTIONAL

all_students

-radius

RADIUS

SERVER

RADIUS

AUTHENTICATION
USED

OPTIONAL

YES OR NO

yes

acl up

This command pushes an identity position up in priority.

acl up

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-ta

TARGET

TARGET ALAIS

MANDATORY

sql

-id

IDENTITY

NAME OF

ACL

MANDATORY

Med_School

-n

JUMP SIZE

NUMBER OF PLACES
TO MOVE UP

OPTIONAL

DEFAULT

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 276 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: