SANRAD I3.1.1205 User Manual Download Page 231

Page: 231 / 348

Chapter 11: Command Line Interface

11-17

neighbor show

This command lists the neighbor(s) in a cluster.

neighbor show

Table

11-10: Neighbors in a Cluster

Name

IP Address

UDP SNMP Timeout

(msec)

SNMP # of
Retries

VSwitch2 212.199.43.75 161 1500

neighbor details

This command lists the details of a neighbor in a cluster.

neighbor details

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-nb

NEIGHBOR

ALIAS OF NEIGHBOR
IN CLUSTER

MANDATORY

VSwitch2

Table

11-11: Neighbor Details

Neighbor Name

VSwitch2

IP Address

212.199.43.75

Last Received Keep Alive:

Status Alive

Lock Status

srOpen

neighbor remove

This command removes a V Switch from a cluster.

neighbor remove

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-nb

NEIGHBOR

ALIAS OF NEIGHBOR
TO ADD TO
CLUSTER

MANDATORY

VSwitch2

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 231 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: