manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 183 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 183

 

 

Chapter 9:  Routine Volume Maintenance  

9-5

 

volume replace 

You need to define two parameters to replace a volume: 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-vol 

VOLUME

 

VOLUME ON FAILED 
DISK

 

MANDATORY

 

Simple4 

 

-nvol 

NEW VOLUME

 

REPLACEMENT 
VOLUME

 

MANDATORY

 

Simple6 

Synchronizing a Volume 

 

You can replace a failed volume in a mirror.  You must then synchronize 
the new volume to the original mirrored volumes.  See the working 
example:  Appendix A “

Replacing a Mirrored Volume

”. 

volume mirror sync 

 

You need to define two parameters to synchronize a volume: 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-src 

SOURCE VOLUME

 

ORIGINAL VOLUME 
TO SYNCHRONIZE 
TO

 

MANDATORY

 

Simple3 

 

-dst 

DESTINATION 
VOMUE

 

NEW VOLUME TO 
ADD TO 
SYNCHRONINZE

 

MANDATORY

 

Simple5 

Example: 

The volume Simple3 is synchronized to the volume Simple5. 

volume mirror sync –src Simple3 –dst Simple5 

If you are working in a cluster, the volume will be displayed in the state need 
sync on both V-Switches.  Synchronize the volume on the exposing V-Switch 
using the CLI command 

volume mirror sync

.  

 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments