manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 78 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 78

 

 

4-26 

SANRAD V-Switch CLI User Manual

 

Checking IP Routes 

After creating an IP routing path, you can ping any IP-connected device from 
the V-Switch Eht1 to check that the routing is configured correctly.  Use the CLI 
command 

ping 

to ping an IP address from the V-Switch.  Make sure that the 

route is defined on the other side as well. 

ping 

You need one parameter to check an IP routing path from the V-Switch. 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-ip 

IP

 ADDRESS

 IP

 ADDRESS TO 

PING

 

MANDATORY

 

172.17.200.69 

ping –ip 172.17.200.69  

Viewing IP Routes 

After creating an IP routing path to an external network, you can view it and 
any other configured IP routing path.  Use the CLI command 

ip route show 

to view a V-Switch’s routing table. 

ip route show 

Table 

 

4-6: 

V-Switch IP Routing Paths 

 Dest 

IP 

Address 

Dest Mask 

Interface

Gateway 

TOS

 10.10.20.20 

255.255.255.0

Eth2 

30.30.20.20 

 

 10.12.40.40 

255.255.255.0

Eth3 

20.22.11.11 

 

Removing an IP Route 

You can remove unwanted IP routing paths from your V-Switch.  Use the CLI 
command 

ip route remove

 to remove an IP routing path.  If you are 

working in a V-Switch cluster, the IP route must be removed from both V-
Switch databases.  For more information on V-Switch clusters, see 
“

Introduction to V-Switch Clusters

”. 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments