SANRAD I3.1.1205 User Manual Download Page 248

Page: 248 / 348

11-34

SANRAD V-Switch CLI User Manual

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-sus

STRIPED UNIT SIZE

NUMBER OF BLOCKS
TO WRITE IN EACH
VOLUME PER PASS

MANDATORY

200

-nbc

NUMBER OF
CHILDREN

NUMBER OF
VOLUMES TO
CREATE STRIPE
ACROSS

OPTIONAL

DEFAULT

-ch

CHILD

ALIAS OF EACH
VOLUME IN STRIPE

MANDATORY

Simple3

-ch

CHILD

ALIAS OF EACH
VOLUME TO
INCLUDE IN
MIRROR

MANDATORY

Simple4

volume set

This command will change a volume alias or load threshold.

volume set

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-vol

VOLUME

ALIAS OF VOLUME
TO CHANGE

MANDATORY

Subdisk7

-na

NEW ALIAS

NEW ALIAS FOR
VOLUME

MANDATORY IF
CHANGING ALIAS

Simple7

-lt

LOAD THRESHOLD

PERCENTAGE FULL
AT DESTINATION
TO TRIGGER AN
ALARM

MANDATORY IF
CHANGING LOAD
THRESHOLD

volume remove

This command removes a volume from the system. The volume must be at the
top of the hierarchy. The volume cannot be exposed; the volume LU must be
inactivated.

volume remove

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-vol

VOLUME

ALIAS OF VOLUME
TO REMOVE

MANDATORY

Stripe3

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 248 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: