manualshive.com logo in svg

SANRAD I3.1.1205, User Manual, Page: 201 / 348

Share
Download
SANRAD I3.1.1205 User Manual Download Page 201

 

 

Chapter 10:  Routine V-Switch Maintenance  

10-15

 

 

 

 

Disks and Subdisks 

Discovering Storage Devices 

The V-Switch default algorithm for storage devices discovery is using the SCSI 
command REPORT LUNS.  Certain storage devices either do not support this 
command or do not respond according to the SCSI standard.  To discover these 
devices, the REPORT LUNs command must be disabled.  If certain devices in 
the SAN are not being discovered by the V-Switch, use the CLI command 

device set 

to disable or re-enable device discovery via REPORT LUNs. 

device set 

You need to define one parameter to change the V-Switch storage device 
discovery mode: 

 

S

WITCH

 

P

ARAMETER

 

D

EFINITION

 

S

TATUS

 

E

XAMPLE

 

 

-rld 

REPORT 

LUN

 

DISCOVERY

 

MODE FOR 
DISCOVERING 
DEVICE 

LUN

S

 

MANDATORY

 

YES OR NO

 

DEFAULT

:

  YES

 

no 

See “

device set

,” for the full list of switch parameters for the CLI command 

device set

. 

Summary of Contents for I3.1.1205





























































































































































































































































































































































Reviews:

No comments