SANRAD I3.1.1205 User Manual Download Page 129

Page: 129 / 348

Chapter 7: Volume Exposure and Security

7-11

You need to define three parameters to create an iSCSI target:

WITCH

ARAMETER

EFINITION

TATUS

XAMPLE

-ta

TARGET ALIAS

USER

ASSIGNED

ALIAS FOR I

SCSI

TARGET

MANDATORY

finance

–tn

TARGET WWUI

USER

ASSIGNED

WORLD

WIDE

UNIQUE IDENTIFIER
FOR THE TARGET

MANDATORY

sanrad.
billing

–device

DEVICE

ALIAS OF

V-

WITCH TO EXPOSE

TAREGT ON

MANDATORY

VSwitch1

Example:

If you are working in

a V-Switch cluster,

each target must be

configured on both V-

Switches.

The target finance is created on V-Switch 1. The WWUI of Finance is
billing.sanrad, as shown in Figure

7-10.

iscsi target create –ta finance –tn sanrad.billing –
device VSwitch1

Summary of Contents for I3.1.1205





























































































































































































































































































































































Search results

Summary of Contents for I3.1.1205

Reviews:

SANRAD I3.1.1205, User Manual, Page: 129 / 348

Search results

Summary of Contents for I3.1.1205

Reviews: