![background image](http://html1.mh-extra.com/html/sacmi/ccm001/ccm001_user-manual_3187258137.webp)
002AZ001A
8 - 31
MAINTENANCE
8
8.1.2.5.1
Sharpening the cutters
- Loosen the two screws (26) and remove the cutter (25).
- Use an oilstone on the worktable with clamp to sharpen the cutting edges.
- Install the cutters and adjust as directed in the ADJUSTING THE CUTTER paragraph in chapter 7.
8.1.2.5.2
Replacing the cutters
- Loosen the two screws (26) and remove the cutter (25).
- Install the new cutter.
- Adjust the height of the cutter as directed in the ADJUSTING THE CUTTER paragraph in chapter 7.
8.1.2.5.3
Cleaning the cutters
- Loosen the screws (13 and 16) and ring nut (17).
- Pull out the insertion drum lifting the entire unit up from the cutter holder.
- Loosen the screw (18) at the worktable.
- Take out the cutter holder.
- Loosen the screws (23) and remove the cutter.
- Clean the cutter removing any burrs of plastic compound. Scour the part with a diluent.
- Install the cutter (24) by tightening the screws (23).
- Attach the cutter holder to the drum with screws (18).
- Install the drum on the shaft and tighten screws (13 and 16) and ring nut (17).
- Adjust the height of the cutter, time the wheel and adjust the exit channel as directed in the ADJUSTING THE
CUTTER and ADJUSTING THE PELLET INSERTION STAGE paragraphs in chapter 7.
8.1.2.5.4
Replacing the cutters
- Loosen the screws (13 and 16) and ring nut (17).
- Pull out the insertion drum lifting the entire unit up from the cutter holder.
- Loosen the screw (18) at the worktable.
- Take out the cutter holder.
- Loosen the screws (23) and replace the cutter.
- Install the cutter (25) previously removed from the old cutter.
- Install the cutter by tightening the screws (23).
- Attach the cutter holder to the drum with screws (18).
- Install the drum on the shaft and tighten screws (13 and 16) and ring nut (17).
- Adjust the height of the cutter, time the wheel and adjust the exit channel as directed in the ADJUSTING THE
CUTTER and ADJUSTING THE PELLET INSERTION STAGE paragraphs in chapter 7.
8.1.2.5.5
Cleaning the nozzles
- Loosen the screws (13 and 16) and ring nut (17).
- Pull out the insertion drum lifting the entire unit up from the cutter holder.
- Loosen the screw (18) at the worktable.
- Take out the cutter holder.
- Loosen the screws (23) and remove the nozzle.
- Check the condition of the seals, replacing them if worn down.
- Clean the nozzle (35) with diluent. Blow compressed air in the holes to eliminate any obstructions.
- Install the nozzle securing it with the cutter with screws (23).
- Attach the cutter holder to the drum with screws (18).
- Install the drum on the shaft and tighten screws (13 and 16) and ring nut (17).
- Adjust the height of the cutter, time the wheel and adjust the exit channel as directed in the ADJUSTING THE
CUTTER and ADJUSTING THE PELLET INSERTION STAGE paragraphs in chapter 7.
Summary of Contents for CCM001
