manualshive.com logo in svg

RS PRO 917-6298, Instruction Manual

Share
Download
RS PRO 917-6298 Instruction Manual Download Page 68

IIT-2000/2010/5000/5010 Instruction Manual/English

 

 

66  

05/08/2015 Version No. 001

 

 

4.  Press the EDIT/SAVE key to save and exit the 

MANU Utility menu. 

EDIT/SAVE

 

 Note 

The ESC key can be pressed at any time in the MANU Utility 

menu to cancel and exit. 

Setting the Grounding Mode 

 

Background 

When GROUND MODE is set to ON, the IIT-2000/ 

2010/5000/5010 grounds the return terminal to the ground. 

This mode is best for DUTs that are grounded to an earth 

ground by their chassis, fixtures or operation environment. 

This mode measures the potential of the HIGH VOLTAGE 

terminal with respect to earth ground. This means that any 

stray capacitance/resistance that leaks to earth ground will 

also be measured. This is the safest testing mode, though 

potentially not as accurate. 

When GROUND MODE is set to OFF, the return terminal is 

floating with respect to the earth ground. This mode is for 

DUTs that are floating and not directly connected to an earth 

ground. This is more accurate than when GROUND MODE is 

set to ON as any stray capacitance/resistance that leaks to the 

earth ground from the DUT side of the testing circuit will not be 

measured. For this reason, this testing mode is able to 

Summary of Contents for 917-6298






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands