manualshive.com logo in svg

RS PRO 917-6298, Instruction Manual

Share
Download
RS PRO 917-6298 Instruction Manual Download Page 166

IIT-2000/2010/5000/5010 Instruction Manual/English

 

 

164  

05/08/2015 Version No. 001

 

Example 

MANU:DCW:CHIS 5 

Sets the DCW HI SET current to 5mA. 

MANU:DCW:CLOSet 

Set

Query

 

 

Description 

Sets or returns the DCW LO SET current value in milliamps. The 

LO SET value must be less than the HI SET value.  The test must 

first be in DCW mode before this command can be used. 

The LO SET range must use the HI SET range. If all the digits in 

the LO SET range are outside the HI SET range, an error will be 

produced. All digits outside the HI SET range are ignored and will 

not be used. 

For example: 

HI SET value: 12.34  

LO SET value1: 0.005 

 error 

LO SET value2: 0.053 

 no error 

In the example above LO SET value1 will produce an error as all 

digits are outside the range of HI SET. LO SET value2 will not 

produce an error, but will return 0.05, not 0.053. 

Syntax 

Query Syntax 

MANU:DCW:CLOSet<NR2> 

MANU:DCW:CLOSet? 

Parameter/ 

Return 

parameter 

<NR2>  0.000 ~ 010.9 (IIT-2000/2010) 

0.000 ~ 020.9 (IIT-5010/5000) 

Summary of Contents for 917-6298






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands