RS PRO 917-6298 Instruction Manual Download Page 160

Page: 160 / 221

IIT-2000/2010/5000/5010 Instruction Manual/English

158

05/08/2015 Version No. 001

Example

MANU:ACW:VOLT 1

Sets the ACW voltage to 1 kV.

MANU:ACW:CHISet

Set

Query

Description

Sets or returns the ACW HI SET current value in milliamps. The

test must first be in ACW mode before this command can be

used.

Syntax

Query Syntax

MANU:ACW:CHISet <NR2>

MANU:ACW:CHISet?

Parameter/

Return

parameter

<NR2> 0.001 ~ 042.0 (IIT-2000/2010)

0.001 ~ 110.0 (IIT-5010/5000)

Example

MANU:ACW:CHIS 10.0

Sets the ACW HI SET current to 10 mA.

MANU:ACW:CLOSet

Set

Query

Description

Sets or returns the ACW LO SET current value in milliamps. The

LO SET value must be less than the HI SET value. The test must

first be in ACW mode before this command can be used.

The LO SET range must use the HI SET range. If all the digits in

the LO SET range are outside the HI SET range, an error will be

Summary of Contents for 917-6298






























































































































































































































Search results

Summary of Contents for 917-6298

Reviews:

Brands by name

Popular brands

RS PRO 917-6298, Instruction Manual

Search results

Summary of Contents for 917-6298

Reviews:

Brands by name

Popular brands