RS PRO 917-6298 Instruction Manual Download Page 6

Page: 6 / 221

IIT-2000/2010/5000/5010 Instruction Manual/English

05/08/2015 Version No. 001

Frame or Chassis Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as unsorted municipal

waste. Please use a separate collection facility or contact the

supplier from which this instrument was purchased.

Safety Guidelines

General

Guideline

CAUTION



Do not place any heavy object on the instrument.



Avoid severe impact or rough handling that leads to damaging

the instrument.



Do not discharge static electricity to the instrument.



Use only mating connectors, not bare wires, for the terminals.



Do not block the cooling fan opening.



Do not disassemble the IIT-2000/2010/5000/5010 unless you

are qualified.

(Measurement categories) EN 61010-1:2010 specifies the measurement

categories and their requirements as follows. The IIT-2000/2010/5000/5010 does

not fall under category II, III or IV.



Measurement category IV is for measurement performed at the source of low-

voltage installation.



Measurement category III is for measurement performed in the building

Summary of Contents for 917-6298






























































































































































































































Search results

Summary of Contents for 917-6298

Reviews:

Brands by name

Popular brands

RS PRO 917-6298, Instruction Manual

Search results

Summary of Contents for 917-6298

Reviews:

Brands by name

Popular brands