RS PRO 917-6298 Instruction Manual Download Page 167

Page: 167 / 221

IIT-2000/2010/5000/5010 Instruction Manual/English

05/08/2015 Version No. 001

165

Example

MANU:DCW:CLOS 2.00

Sets the DCW LO SET current to 2mA.

MANU:DCW:TTIMe

Set

Query

Description

Sets or returns the DCW test time in seconds. The test must first

be in DCW mode before this command can be used.

In special MANU mode, the TIMER can be turned off.

Syntax

Query Syntax

MANU:DCW:TTIMe {<NR2>|OFF}

MANU:DCW:TTIMe?

Parameter

<NR2>

OFF

0.5 ~ 999.9 seconds

TIMER OFF (special MANU mode).

Return

parameter

<NR2>

TIME OFF

0.5 ~ 999.9 seconds

TIMER is OFF (special MANU mode).

Example

MANU:DCW:TTIM 1

Sets the DCW test time to 1 second.

MANU:DCW:REF

Set

Query

Description

Sets or returns the DCW reference value in mA. The test must

first be in DCW mode before this command can be used.

The reference value must be less than the HI SET value.

The reference value uses the same range as the HI SET value.

Summary of Contents for 917-6298






























































































































































































































Search results

Summary of Contents for 917-6298

Reviews:

Brands by name

Popular brands

RS PRO 917-6298, Instruction Manual

Search results

Summary of Contents for 917-6298

Reviews:

Brands by name

Popular brands