manualshive.com logo in svg

RS PRO 917-6298, Instruction Manual

Share
Download
RS PRO 917-6298 Instruction Manual Download Page 119

 

IIT-2000/2010/5000/5010 Instruction Manual/English

 

05/08/2015 Version No. 001 

117

 

 

7.  Press EDIT/SAVE to save the settings and exit to 

VIEW status. 

EDIT/SAVE

 

 Note 

Ensure the baud rate settings or GPIB address matches the 

host machine. 

 Note 

The ESC key can be pressed at any time to cancel and exit 

back to VIEW status. 

Control Settings 

 

Description 

The Control settings are accessed in the COMMON UTILITY 

menu. The Control settings include: Start Control, Double 

Action, Key Lock and Interlock. 

Start Control is used to determine how a test is started. Tests 

can be started via the front panel (START/STOP buttons), 

from a remote controller or via the SIGNAL I/O port. 

The Double Action function is a safety feature used to prevent 

accidentally starting a test. Normally to start a test, the START 

button is pressed when the tester is in the READY status. To 

start a test when Double Action is ON, the STOP button must 

first be pressed, followed by the START button within 500ms.  

Key Lock disables the front panel keys from changing the test 

Summary of Contents for 917-6298






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands