Richmond GTR058 User Manual Download Page 1

Page: 1 / 31

GTR058 Installation Manual:

Rev 22

Double Swing Gate Opener

User Manual

GTR058

Instructions must be read before beginning installation. Please follow these instructions carefully,

incorrect installation could affect gate operation. If you require more information, please contact

your local Richmond Wheel & Castor Co branch.

AU:

1300 474 246

NZ:

0800 61 71 81

International:

+613 9551 2233

For installation or troubleshooting assistance visit

richmondau.com/gate-motor-support/

For accessories:

please refer to the relevant accessory manuals for instructions on wiring them to the GTR058 motor.

Before starting we recommend watching the installation video that can be found at:

richmondau.com/product/gtr058-double-swing-gate-opener/

This video will give a detailed overview of the installation process and will serves as a useful aid during installation.

Summary of Contents for GTR058
































Search results

Summary of Contents for GTR058

Reviews:

Related manuals for GTR058

Brands by name

Popular brands

Richmond GTR058, User Manual

Search results

Summary of Contents for GTR058

Reviews:

Related manuals for GTR058

Brands by name

Popular brands