37
NOTE:
The remote wires must be connected to the
3-pin connector before the connector is plugged into the
board.
2-Wire Remote Control (On-Off)
This application assumes that only one heating function
(pool or spa) is required.
1. Turn on power to the heater.
2. For a 2-Wire Remote Control from a remote without
its own sensor, push the MODE key to the “POOL” or
“SPA” mode and set the desired setpoint (e.g.102°F
(39°C) for Spa).
3. For a 2-Wire Remote Control from a remote with its
own sensor, push the MODE key to select “POOL” or
“SPA” mode and set the temperature to the highest
setting available on the control. The actual setpoint will
be controlled by the remote control.
4. Turn the MODE button to "OFF" and remove power
from the heater.
5. On the “Remote Interface Harness”, connect the
BLUE wire to one side of the “REMOTE” switch and
connect the other side to either the ORANGE/BLACK
wire for “SPA” operation or the BLACK/ORANGE wire
for “POOL” operation. See
Figure 57
.
6. Attach wire nut on the unused wire to the “Remote
Interface Harness.”
7. Install the “3-wire Remote Control Harness” to the P8
connector and turn power "ON" to the heater. See
Figure 57
.
SET POOL
(BLACK WITH ORANGE)
SET SPA
(ORANGE WITH BLACK)
24VAC
(BLUE)
Figure 56. 3-Wire Remote Interface Harness
SPA
COMMANDS
POOL
COMMANDS
OR
REMOTE SPA
SWITCH
REMOTE POOL
SWITCH
BLUE - 24 VAC OUTPUT
BLUE - 24 VAC OUTPUT
WIRE NUT BK/ORN
WIRE NUT ORN/BK
Figure 57. 2-Wire Remote Harness Installation
3-Wire Remote Control Using Three-
Position Switch (Pool-Off-Spa, or Low-Off-
High)
This application assumes that both heating functions (pool
and spa) are required.
1. Turn on power to the heater.
2. Push the MODE key to the “POOL” or “SPA” mode
and set the desired temperature for each (e.g. 80°F
(27°C) for Pool and 102°F (39°C) for Spa).
3. Turn the MODE key to "OFF" and remove power from
the heater.
4. On the “Remote Interface Harness” connect the BLUE
wire to one side of the “REMOTE” switch and connect
the ORANGE/BLACK wire for “SPA” operation and
the BLACK/ORANGE wire for the “POOL” operation.
See
Figure 57.
5. Install the “Remote Interface Harness” to the P8
connector and turn power ON to the heater. See
Figure 58
.
For activation of the remote control, see
"Activating the
Remote"
on page
36
.
POOL AND SPA
COMMANDS
REMOTE POOL
AND SPA SWITCH
BLUE - 24 VAC OUTPUT
Figure 58. 3-Wire Remote Harness Installation
Summary of Contents for AVIA 264A
