background image

Effective: 03-11-22

Replaces: 241807 Rev. 7

P/N: 100-10000111 Rev. 1

This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future 

reference.

WARNING:

 

If the information is not followed exactly, a fire or explosion may result causing property 

damage, personal injury or death. 

— Do not store or use gasoline or other flammable vapors and liquids or other combustible materials 

in the vicinity of this or any other appliance. To do so may result in an explosion or fire.

— WHAT TO DO IF YOU SMELL GAS

 

•   Do not try to light any appliance.

  •   Do not touch any electrical switch; do not use any phone in your building.
  •   Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
  •   If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.

INSTALLATION AND  

OPERATION MANUAL

Gas-Fired Pool 

and Spa Heater

Models 264 and 404

Summary of Contents for AVIA 264A































































































































































Reviews: