Printronix PrintNet P8000 Line User Manual Download Page 221

Page: 221 / 240

221

Customer Support

Printronix Customer Support Center

IMPORTANT

Please have the following information available prior to calling
the Printronix Customer Support Center:

•

Model number

•

Serial number (located on the back of the printer)

•

Installed options (i.e., interface and host type if applicable to
the problem)

•

Configuration printout:

Thermal Printer

See “Printing A Configuration” in the

Quick Setup Guide

Line Matrix Printer

Press PRT CONFIG on the control panel, then press Enter.

•

Is the problem with a new install or an existing printer?

•

Description of the problem (be specific)

•

Good and bad samples that clearly show the problem (faxing or
emailing of these samples may be required)

Americas

(714) 368-2686

Europe, Middle East, and Africa

(31) 24 6489 311

Asia Pacific

(65) 6548 4114

China

(86) 800-999-6836

http://www.printronix.com/support.aspx

Summary of Contents for PrintNet P8000 Line

















































































































































































































































Search results

Summary of Contents for PrintNet P8000 Line

Reviews:

Related manuals for PrintNet P8000 Line

Brands by name

Popular brands

Printronix PrintNet P8000 Line, User Manual

Search results

Summary of Contents for PrintNet P8000 Line

Reviews:

Related manuals for PrintNet P8000 Line

Brands by name

Popular brands