SERIES-300 SCS
PAG OERLIKON AG
DISMANTLING / ASSEMBLY INSTRUCTIONS
D 03.02
6. Dismantling the weight support
(1/B11.02)
- Undo 2 screws (10/B11.01) of the weight support, remove the weight support
Important: Do not dismantle any prisms, assembly only possible with gauge
7. Dismantling the flexure strap
(7/B04.01)
- Undo the balance arm (12/B04.01) and the support piece (10.B04.01) with 2 auxiliary bolts D3 [1]
{Fig. 2}
- Undo 2 screws (21/B04.01) of the flexure strap, remove the flexure strap
8. Dismantling the flexure holders
(2/B04.01)
- Undo 4 screws (29/B04.01) of the top flexure holder {2 pts. on the chassis, 2 pts. on the support piece}
- Remove the top flexure holder including the flexure sheets
- Turn over the chassis cpl., put pot magnet on mounting gauge [9]
- Undo 4 screws (29/B04.01) of the bottom flexure holder {2 pts. on the chassis, 2 pts. on the support
piece}
- Remove the bottom flexure holder including the flexure sheets
9. Dismantling the signal coil
- Undo 4 screws (30/B04.01) of the cover (9/B04.01), remove the cover
- Unsolder 2 connection wires (26/B04.01) from the board of the signal coil
- Undo 2 brass screws (15/B04.01) of the signal coil on the balance arm
- Take the signal coil out of the pot magnet
10. Dismantling the balance arm cpl.
(12/B04.01)
from the chassis
(19/B04.01)
- Undo the brass screw (15/B04.04) of the vane (24/B04.01), remove the vane from the sensor
mechanism (18/B04.01)
- Undo 2 screws (27/B04.01) of the flexure sheets (13/B04.01) of the chassis
- Undo 2 screws [10] of the fixing blocks [4] of the chassis
- Remove undone the balance arm cpl. from the chassis
11. Dismantling the support piece
(10/B04.01)
from the balance arm
(12/B04.01)
- Remove 2 auxiliary bolts D3 [1] from the support piece and the balance arm
- Remove the support piece from the balance arm {shorter side first}
12. Dismantling the flexure sheets
(13/B04.01)
- Undo 2 screws (28/B04.01) of the flexure sheets, take the flexure sheets from the balance arm
13. Dismantling the fixing blocks
[4]
and the stopper
(22/B04.01)
- Undo 2 screws [10] of the fixing blocks [4], remove the fixing blocks [4]
- Screw the plastic stopper from the chassis
Fig.2
1
12
10
Summary of Contents for 300 SCS series
