SERIES-300 S / SIP
PAG OERLIKON AG
DISMANTLING / ASSEMBLY INSTRUCTIONS
D 02.04
12
14
16
15
19
3a
3b
Fig.7
14. Assembly of the balance arm cpl.
(12/B04.01)
in the chassis
(19/B04.01)
- Swing on the balancce arm cpl. carefully into the chassis, until the flexure sheets just touch the chassis
- Fasten 2 flexure sheets (13/B04.01) with 2 screws (27/B04.01), 2 washers (5/B04.01), 2 spring washers
(6/B04.01) and 2 bases (36/B04.01) free of tension onto the chassis {do not twist the bases}
15. Secure the weighing cell
- Connect 2 fixing blocks with 2 screws [10] to the chassis
- Lightly undo the brass screw (15/B04.01) of the stopper (14/B04.01) on the balance arm, turn the
stopper 90° away from the pot magnet
- Screw the auxiliary stop [3b] by hand into the chassis
- Turn the stopper (14/B04.01) 90° back to the pot magnet, lightly tighten the brass screw (15/B04.01)
- Undo the auxiliary stop [3b] by hand until it is in line with the stopper
- Screw the knurled nut [3a] by hand onto the auxiliary stop [3b] until the stopper is clamped {Fig. 7}
16. Checking the annular clearance between the magnet and the pot magnet
- Drive the auxiliary pin [6] in vertically into the annular clearance between the magnet and the pot
magnet
- Move with circular motion 360° around the magnet, when 360° -> annular clearance O.K.
- When not O.K. -> undo 3 space bolts on the underneath of the chassis a little
- Drive the centring bolt [7] from below into the magnet, re-tighten 3 space bolts
- Remove the centring bolt [7], check the annular clearance again!
17. Cleaning the annular clearance and spool
(1/B04.01)
- Cut a strip of double-sided sticky tape {ca. 2 x 2 cm}
- Wind the sticky tape around one end of a toothpick
- Guide the toothpick vertically with the sticky tape forward into the annular clearance
- Move with a circular motion several times around the magnet {all dirt will stick to the sticky tape}
- Same procedure to clean the spool
18. Assembly of the spool
(1/B04.01)
- Carefully guide the spool into the annular clearance between the magnet and the pot magnet {note
the position}
- Guide the centring bolt [7] vertically through the spool into the magnet {centring}
- Fasten the spool with 2 brass screws (15/B04.01) and 2 washers (16/B04.01) on the balance arm
(12/B04.01)
- Remove the centring bolt [7] again, screw on the cover (9/B04.01) with 4 screws (30/B04.01)
Summary of Contents for 300 SCS series
