manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 96 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 96

Prog.no. 2444: With this parameter the maximum boiler capacity for the 

DHW mode can be restricted.

Note

These are calculated values. The actual output must be calculated 

using a gas meter, for example.

Controller delay (2450)

The controller delay is used for a stabilisation of the combustion condi­

tions, especially after a cold start. After release of the firing automation by 

the controller this remains on the set output for a specified time. Modula­

tion is only released after this time has elapsed.
Prog. no. 2450 is used to set the operating mode at which the controller 

delay is active.

Controller delay fan output (2452)

Boiler capacity which is used during the duration of the control delay.

Controller delay duration (2453)

Duration of the control delay. The time duration starts as soon as a posi­

tive flame is detected after ignition.

Switching diff on CHs (2454), Switching diff off min CHs 

(2455), Switching diff off max CHs (2456), (2460), Switching diff on 

HW (2461) and Switching diff off min HW (2462)Switching diff off 

max HW

Sd Switching difference off

Sd1 Switching diff off max CHs, Switching diff off max HW

Sd2 Switching diff off min CHs, Switching diff off min HW

Sd3 Switching diff on CHs, Switching diff on HW

t Time

Ti Actual temperature

To avoid unnecessary switch off during transient effects the switch-off dif­

ference adapts dynamically depending on the temperature profile (see 

fig.).

Delay heat req special op (2470)

The heat request during special operation (chimney-sweep function, con­

troller stop, manual operation) is sent to the burner delayed by the time set 

here. In this way slowly opening mixers can already start up before the 

burner goes into operation. Thus a boiler temperature that is too high can 

be prevented.

Pressure switch shutdown (2500)

This function checks the static water pressure with the aid of the connec­

ted water pressure switch. Depending on the option set (

Start prevention 

or 

Lockout position

) a start prevention or lockout position is carried out 

with a corresponding diagnosis.
A closed water pressure switch releases the startup of the burner control 

and the actuation of the pumps. A start prevention or lockout position is 

triggered with the pressure switch open.
The pump actuation is also locked for protection against dry running. If the 

water pressure increases again and the switch closes again, this is auto­

matically cancelled again with a start prevention and the pump actuation is 

released again.

Gas energy metering (2550)

This parameter is used to switch gas energy metering on or off. The coun­

ter values are not deleted during this process.

Fig.29 Switching difference

t

Sd

Sd1

Sd2

Sd3

RA-0000079

Ti

Ti

9  Settings

96

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Reviews:

No comments