manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 83 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 83

End of holiday (643 - 663)

Entering the holiday end.

Operating level (648-668)

Selection of the operating level (Reduced or Off) for the holiday pro­

gramme

Note

A holiday period always ends on the last day at 12:00 AM (23:59). 

The holiday programmes are only activated in the operation mode 

Automatically.

See

Refer to the user instructionsParamount four.

9.2.6  Heating circuits

Operating mode (700, 1000, 1300)

The operating mode can be set via the operation mode button at the room 

device or via this operating line.

Off: The heating is switched off in protection mode. The room remains 

protected against frost however (Frost protection setpoint, e.g. prog. no. 

714).

Timed: In automatic mode the room temperature is controlled in accord­

ance with the time program selected.

Reduced: In reduced operation mode the room temperature is kept con­

stantly to the set Reduced temp setpoint(e.g. prog. no. 712).

On: In comfort mode the room temperature is kept constantly to the set 

Comfort setpoint(e.g. prog. no. 710). Eco functions are not activated.

Comfort setpoint (710, 1010, 1310)

Setting of the comfort setpoint in the heating phases. Without room sensor 

or with the room influence switched off (prog.no. 750, 1050, 1350), this 

value is used for calculation of the flow temperature, to theoretically reach 

the set room temperature.

Reduced temp setpoint (712, 1012, 1312)

Setting of the desired room temperature during the reduced heating 

phase. Without room sensor or with the room influence switched off 

(prog.no. 750, 1050, 1350), this value is used for calculation of the flow 

temperature, to theoretically reach the set room temperature.

Frost protection setpoint (714, 1014, 1314)

Setting of the required room temperature during frost protection mode. 

Without room sensor or with the Room influence(prog.no. 750, 1050, 

1350), this value is used for calculation of the flow temperature, to theoret­

ically reach the set room The heating circuit remains turned off until the 

flow temperature drops so far that the room temperature falls below the 

frost protection temperature.

Heating curve slope (720, 1020, 1320)

Using the heating curve, the flow temperature setpoint is formed that is 

used to regulate the heating circuit, subject to the outside temperature. 

The gradient indicates how much the flow temperature changes by with 

changing outside temperature.

9  Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

83

Summary of Contents for Paramount four

















































































































































Reviews:

No comments