manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 115 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 115

ted by the master. The time of the controller is then continually adapted 

to the system time.

Master: The time can be adjusted at the controller. The controller time is 

defaulted to the system. The system time is adapted.

Outside temp source (6650)

In the LPB system only one single outside temperature sensor is necessa­

ry. This delivers the signal via the LPB to the controllers without a sensor. 

The first figure in the display is the section number, the second is the ap­

pliance number.

9.2.19 Fault

Message (6700)

A current existing error in the system is displayed here in the form of an 

error code.

Display SW diagnostic code (6705)

In case of a fault, the display fault is on permanently. In addition, the diag­

nosis code is displayed on the display.

Burn ctrl phase lockout pos (6706)

Phase during which the fault occurred which led to the failure.

Reset alarm relay (6710)

An output relay QX, programmed as an alarm relay can be reset via this 

setting.

Flow temp 1 alarm (6740), Flow temp 2 alarm (6741), Flow 

temp 3 alarm (6742), Boiler temp alarm (6743) and Hot water 

charging alarm (6745)

Setting the time after which a fault message will be triggered in case of 

persisting deviation from temperature nominal and actual values.

Error history / Error codes (6800-6995)

The last 20 error messages with error codes and time of occurrence are 

saved to the error memory.

9.2.20 Maintenance / special operation

Burner hours interval (7040)

Setting of the interval for maintenance of the burner.

Burn hrs since maintenance (7041)

Burner hours since the last maintenance.

Note

The burner hours are only counted, when the maintenance mes­

sage has been activated.

Burner start interval (7042)

Setting of the interval for burner starts for maintenance.

Burn starts since maint (7043)

Burner starts since the last maintenance.

Note

The burner starts are only counted, when the maintenance mes­

sage has been activated.

Maintenance interval (7044)

Setting of maintenance interval in months.

Time since maintenance (7045)

Passed time since the last maintenance interval.

9  Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

115

Summary of Contents for Paramount four

















































































































































Reviews:

No comments