Potterton Paramount four Installation Manual Download Page 125

Page: 125 / 144

End user (Eu)

Commissioning, Engineer (menu

Status)

Overtemp protect active

Released

Locked, manual

Locked, automatic

Min limitation active

Min limitation

Min limitation, part load

Min limitation active

In operation for CH

Protective start

Protective start, part load

Return limitation

Return limitation, part load

In operation for CH

In part load op for CH

In operation for HW

In part load op for HW

In op for CH, HW

In part load op for CH, HW

Overrun active

In operation

Assisted firing active

Released

Frost protection active

System frost protect active

Boiler frost prot active

Off

Tab.32 Status table burners

The following messages are possible under Burner:

End user (Eu)

Commissioning, Engineer (menu

Status)

Lockout position

Start prevention

In operation

Startup

Safety time

Prepurge

Startup

Postpurge

Shutdown

Home run

Standby

Tab.33 State table buffer storage tank

The following messages are possible under Buffer storage tank:

End user (Eu)

Commissioning, Engineer (menu

Status)

Hot

Frost protection active

9 Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

125

Summary of Contents for Paramount four

















































































































































Search results

Summary of Contents for Paramount four

Reviews:

Potterton Paramount four, Installation Manual, Page: 125 / 144

Search results

Summary of Contents for Paramount four

Reviews: